Teac DR-07MKII Manuale Utente

DR-07@#Linear PCM RecorderD01145020AOWNER’S MANUALThis device has a serial number located inside the battery compartment. Please record it and retain

10 TASCAM DR-07MKIITurning the unit power OFF automatically ... 109Setting the backlight ... 109Adjusting the disp

100 TASCAM DR-07MKII3 A screen to enable/disable the level alignment function appears.4 Use the + or − button to select ON, and press the Á button t

TASCAM DR-07MKII 101The DR-07MKII has built-in eects that can be applied to the input signal during recording and practice. They can also be applied

102 TASCAM DR-07MKIILEVEL:Use this to change the output level of the preset effect selected in the PRESET item.Setting range: 0 - 20SOURCE:Use this t

TASCAM DR-07MKII 103TASCAM DR-07MKII has a built-in tuner. The unit receives a sound from a musical instrument and allows you to tune it accurately o

104 TASCAM DR-07MKIIBy connecting this unit with a computer using the USB cable, you can transfer audio les on the microSD card in the unit to a com

TASCAM DR-07MKII 105Make sure that the microSD card is inserted properly.NOTEIf the USB cable is connected to the unit when batteries has been instal

106 TASCAM DR-07MKIITransferring files from a computer1 Click the “DR-07MK2” drive on the computer screen to show the “MUSIC” and “UTILITY” folders.

TASCAM DR-07MKII 107Viewing File InformationUse the Information Screen to view various types of information about your DR-07MKII.1 Press the MENU but

108 TASCAM DR-07MKIICard information pageThe CARD page shows the status of the currently inserted microSD card.TOTAL MUSICShows the number of playabl

TASCAM DR-07MKII 109System Settings and FormattingFrom the SYSTEM Screen, you can change various settings to optimize the device for your use environ

TASCAM DR-07MKII 11Quick Start GuideTry recording and playback with TASCAM DR-07MKII.The unit contains a factory-installed microSD card, and will by

110 TASCAM DR-07MKIIAdjusting the display contrastUse CONTRAST to adjust the display contrast.Options: 1–20 (factory setting: 5)Setting the type of

TASCAM DR-07MKII 1113 Press the Á button to execute the quick formatting, or press the (HOME) [ª] button to cancel formatting.Using FULL FORMATUse

112 TASCAM DR-07MKIISetting the format of file namesYou can select the format of names given to les recorded by this unit. 1 Press the MENU button t

TASCAM DR-07MKII 113The following is a list of the popup messages that might appear on the DR-07MKII under certain conditions. Refer to this list if

114 TASCAM DR-07MKIIMessage Meaning and responseMBR Error Init CARDThe card is not formatted properly or the formatting is broken. Change the card o

TASCAM DR-07MKII 115Message Meaning and responseCan't DivideThe position selected for divide is not suitable (too close to the beginning or end

116 TASCAM DR-07MKII12–MessagesMessage Meaning and responseNot ContinuedIf any of these errors occurs, turn the unit’s power o and restart it. If

TASCAM DR-07MKII 117If you are having trouble with the operation of this unit, please try the following before seeking repair. If these measures do n

118 TASCAM DR-07MKIIIs the OUTPUT LEVEL setting of the unit •minimized? Recording does not work. ªIf you are using an external device, check the •

TASCAM DR-07MKII 119RatingsRecording mediamicroSD card (64 MB - 2 GB)microSDHC card (4 GB - 32 GB)Recording/playback formatWAV: 44.1/48/96 kHz, 16/24

12 TASCAM DR-07MKII3 Press the RECORD [º] button to switch to recording standby. The REC indicator will flash. NOTEIf the or icon appears in the

120 TASCAM DR-07MKIIAudio performanceFrequency response20 - 20 kHz +1/–3 dB(44.1 kHz, EXT IN to LINE OUT) (JEITA)20 -22 kHz +1/–3 dB(48 kHz, EXT IN t

TASCAM DR-07MKII 121Other specificationsPowerTwo AA batteries (Alkaline or Ni-MH)USB bus power supplied from a computerAC adaptor (TASCAM PS-P515U, s

122 TASCAM DR-07MKII14–SpecificationsRecording/ playbackFormat Operation time NoteRecording MP3 48 KHz, 320KbpsAbout 11 hoursBuilt-in microphonePlayb

TASCAM DR-07MKII 12314–SpecificationsDimensional drawings68mm 26mm158mm90mmDimension of the microphone openedIllustrations and other depictions may d

DR-07@#TEAC CORPORATIONPhone: +81-42-356-9143 http://tascam.jp/1-47 Ochiai, Tama-shi, Tokyo 206-8530 Japan TEAC AMERICA, INC.Phone: +1-323-726-0303

TASCAM DR-07MKII 138 Use the + or – button to control the playback volume. 9 Press the (HOME) [ª] button to stop playback. NOTEIf you have made s

14 TASCAM DR-07MKIIThank you very much for purchasing the TASCAM DR-07MKII Linear PCM Recorder. Please read this Owner’s Manual carefully in order to

TASCAM DR-07MKII 15A QUICK button is available for easy access to •various functionsTrack incrementing function allows a •recording to be split by

16 TASCAM DR-07MKIIEqualizers function for playback, and level •alignment function to enhance the perceived overall sound pressureFile name format c

TASCAM DR-07MKII 17Conventions used in this manualThe following conventions are used in this manual. When we refer to a button or connector or •cont

18 TASCAM DR-07MKIIIntellectual property rightsTASCAM is a registered trademark of TEAC •Corporation.microSDHC Logo is a trademark of SD-3C, LLC.•S

TASCAM DR-07MKII 19Any data, including, but not limited to information, described herein are intended only as illustrations of such data and/or infor

2 TASCAM DR-07MKIIIMPORTANT SAFETY INSTRUCTIONS 1 Read these instructions. 2 Keep these instructions. 3 Heed all warnings. 4 Follow all instructi

20 TASCAM DR-07MKIIAbout microSD cardsThis unit uses microSD cards for recording and playback. microSD cards that are 64 MB - 2 GB and microSDHC card

TASCAM DR-07MKII 21Beware of condensationIf the unit is moved from a cold to a warm place, or used after a sudden temperature change, there is a dang

22 TASCAM DR-07MKIITop panel 1 Built-in stereo microphoneCardioid stereo electret condenser microphone. You can set the microphone angles to open (A

TASCAM DR-07MKII 23this button to answer “NO” to a confirmation message.Press and hold this button to turn the unit’s power ON or OFF.5 + buttonWhen

24 TASCAM DR-07MKIIOn the setting screens, use this button to move the cursor left. On the BROWSE Screen, press this button to move up a level. Press

TASCAM DR-07MKII 25wQUICK buttonWhen playing back, stopped, paused or in recording standby in the Home Screen or when the Playback Control screen is

26 TASCAM DR-07MKIIDuring playback, press this button to start jump-back playback.When a setting screen is open, use this to confirm selections. When

TASCAM DR-07MKII 27Left side paneli /LINE OUT jackUse this to connect with headphones or the line input jack of an amp or other equipment.o HOLD sw

28 TASCAM DR-07MKII2–Names and Functions of PartsBottom Panels Mono speakerUse this built-in speaker to listen to recordings. Sound is not output du

TASCAM DR-07MKII 29Home Screen1 Playback speed setting statusIconPlayback speed x1.0x1.1 - x1.5x0.5 - x0.9Playback speed not controllable2 Loop/rep

TASCAM DR-07MKII 3IMPORTANT SAFETY INSTRUCTIONSCAUTION for products that use replaceable lithium batter-• ies: there is danger of explosion if a bat

30 TASCAM DR-07MKII6Power supply statusWhen a battery is being used, a battery icon shows the amount of power remaining in bars ( , , ). The batt

TASCAM DR-07MKII 31wRemaining timeShows the remaining playback time of the current track (hours: minutes: seconds). ePeak value in decibels (dB)The

32 TASCAM DR-07MKIIRecording ScreenThis screen appears when recording or in recording standby.1 Level control function status : Level control off :

TASCAM DR-07MKII 33The file name that will automatically be given to recorded files is shown.8Recording modeRecording file format, sampling frequenc

34 TASCAM DR-07MKII2–Names and Functions of PartsPlayback Control screenThe Playback Control screen is displayed if the PB CONT button is pressed dur

TASCAM DR-07MKII 35Menu item listThis list provides an overview of the various menu items.Menu item Function PagesREC SETTINGRecording mode settings

36 TASCAM DR-07MKIIUsing menusUse the MENU screen to make various settings. Example: setting the playback area1 Press the MENU button to open the MEN

TASCAM DR-07MKII 37Basic operationUse the following buttons to operate the various screens. MENU button: Opens the MENU screen. PB CONT button: This

38 TASCAM DR-07MKIIPowering the unitDR-07MKII can operate on two AA batteries, or through an optional AC adapter (TASCAM PS-P515U) or USB cable provi

TASCAM DR-07MKII 39CAUTIONNever use any adaptor other than the designated PS- •P515U AC adaptor. Use of a different adaptor could cause malfunction,

4 TASCAM DR-07MKIIinjury or stains around them. If the battery fluid leaks, wipe away any fluid on the battery compartment before insert-ing new ba

40 TASCAM DR-07MKIIStart-up & shutdownCAUTIONThe unit goes in standby mode if shut down when the •unit is operating on AC power supplied through

TASCAM DR-07MKII 41Press the Á button to fix the settings.The start-up screen is displayed, and then the Home Screen appears after the unit has starte

42 TASCAM DR-07MKIISetting the date and timeUsing its internal clock, this unit remembers the date and time when a le is recorded. 1 Press the MENU

TASCAM DR-07MKII 43CAUTIONThe date and time setting can only be maintained for a few minutes if the unit is not powered from batteries or through the

44 TASCAM DR-07MKIICAUTIONDo not remove the microSD card from the unit when it is •connected to a computer by USB.microSD cards that meet microSD or

TASCAM DR-07MKII 45Using the built-in speakerEnable SPEAKER on the MENU screen to allow the unit to play over the built-in speaker.1 Press the MENU

46 TASCAM DR-07MKIIConnecting monitors and headphonesTo listen with headphones, connect them to the /LINE OUT jack.To listen with an external monitor

TASCAM DR-07MKII 47If you open or close the microphone pair while using the built-in stereo microphone and the left-right channels does not suit the

48 TASCAM DR-07MKIICAUTIONSet the left-right channels of the built-in microphone to •R-L. When you are using the built-in microphone and the setting

TASCAM DR-07MKII 494 Use the + button or - button to select (highlight) L-R or R-L depending on the microphone pair’s status.5 Press the Á button t

TASCAM DR-07MKII 5For European Customers ªDisposal of electrical and electronic equipment(a) All electrical and electronic equipment should be dispo

50 TASCAM DR-07MKIIIn addition to using the built-in microphone, you can record using an external microphone or record the output signal from a mixer

TASCAM DR-07MKII 51NOTEHigher values provide better recording quality. •WAV files are higher quality than MP3 files, but they take up •more space,

52 TASCAM DR-07MKII Set the maximum file size with the + or − button to one of the following options.64M, 128M, 256M, 512M, 1G, 2G (default)NOTEIf t

TASCAM DR-07MKII 534–RecordingThe following input settings are made in this screen.Use the  or ¯ button or the + or − button to select the following

54 TASCAM DR-07MKII4–RecordingPlacing the unit and making connectionsRecording with the built-in mics Point the mics at the sound source and place th

TASCAM DR-07MKII 55NOTEThe setting of left-right channels is disabled if an external •microphone is connected to the MIC/EXT IN jack.Adjusting the i

56 TASCAM DR-07MKIIthe input level. Press the  or ¯ button to show a pull-up menu screen for input level setting.If the input is too high, the PEAK

TASCAM DR-07MKII 57Using the Level Control FunctionThe level control function for recording through a microphone is set as follows.1 Press the RECO

58 TASCAM DR-07MKIIcome in. This allows recording level setting to be performed easily.The recording level can be raised manually if required.TIPWhen

TASCAM DR-07MKII 59RecordingBefore starting the following operation procedures, level adjustment should be completed, and the Home Screen should be o

6 TASCAM DR-07MKII(d) The WEEE symbol, which shows a wheeled bin that has been crossed out, indicates that batteries and/or accumulators must be col

60 TASCAM DR-07MKIINOTETo avoid accidental recording of the noise from pressing the RECORD [º] button, the start of recording is delayed by 0.3 secon

TASCAM DR-07MKII 61Select the file you want to overdub1 Use the  and ¯ buttons and the BROWSE screen to select that files that you want to overdub.

62 TASCAM DR-07MKIISimultaneous listening to playback and input sound (Monitor Mix)This allows you to listen to playback and input sound at the same

TASCAM DR-07MKII 637 Use the + or − button to select PB INPUT, and press the ¯ or Á button.8 Use the + or - button to adjust the playback volume le

64 TASCAM DR-07MKII2 While listening to the input sound, use the  or ¯ button to adjust the input level. When the  or ¯ button is pressed, a pull-

TASCAM DR-07MKII 65Start the overdubbing1 Press the RECORD [º] button to set the unit to record standby.The overdubbing ON/OFF pop-up appears.The re

66 TASCAM DR-07MKIIRecording automatically (AUTO REC)The unit starts and pauses recording, renews les, and sets marks automatically depending on the

TASCAM DR-07MKII 677 Use the + or - button to select the level that signal is judged to have been input when it exceeds this level.Set the value to

68 TASCAM DR-07MKIITIPBy using this in combination with the PRE REC function, you can record events without losing the beginnings of sounds.CAUT

TASCAM DR-07MKII 69Files shorter than two seconds cannot be created. •If the name of a newly created file would be the same as •that of an existing

TASCAM DR-07MKII 7Table of ContentsQuick Start Guide ... 111–Introduction ...

70 TASCAM DR-07MKIIMark functionAdding marks manually to a recordingYou can manually add marks to a recording where you want them. Press the MARK b

TASCAM DR-07MKII 71Adding marks automatically to a recordingThis function allows the unit to add marks automatically using AUTO REC. Set the MODE to

72 TASCAM DR-07MKIIRecording the moment before pushing RECORD (PRE REC)By using prerecording, when the unit is in recording standby you can record up

TASCAM DR-07MKII 73Self-timer functionLike a camera, the unit has a self-timer to trigger the start of recording after a set period of time.1 Press R

74 TASCAM DR-07MKIIRecording durationThe table below shows the maximum recording time on microSD/microSDHC cards of dierent capacities for dierent

TASCAM DR-07MKII 75On the BROWSE Screen, you can view the contents of the Music Folder, which contains the audio les on the microSD card that you ca

76 TASCAM DR-07MKIIThis folder that contains this file becomes the current folder, and new recorded file will be saved in this folder. If the playbac

TASCAM DR-07MKII 77File operationsSelect the desired audio le on the BROWSE Screen and press the QUICK button to open the pop-up window that is show

78 TASCAM DR-07MKIIFolder operationsSelect the desired folder on the BROWSE Screen and press the QUICK button to open the pop-up window that is shown

TASCAM DR-07MKII 79Creating a new folderIn the le list, NEW FOLDER appears at the bottom.Select (highlight) NEW FOLDER, and press the Á button. A po

8 TASCAM DR-07MKIITable of ContentsMicrophone position detection ...494–Recording ...50Se

80 TASCAM DR-07MKIIOn the Home Screen, you can use the  and ¯ buttons to select the playback track. The les that you can select are determined by t

TASCAM DR-07MKII 813 Use the + or − button to select (highlight) AREA, and press the ¯ or Á button.4 Use the + or − button to set the playback area

82 TASCAM DR-07MKIISelecting a folder for the playback area (1)Regardless of the current playback area, if you select a folder on the BROWSE Screen,

TASCAM DR-07MKII 83Selecting a folder for the playback area (2)When the playback area is set to FOLDER, if you select a le on the BROWSE Screen, the

84 TASCAM DR-07MKIIPlaylistYou can make a list of tracks for playback (playlist). On the Play Mode Screen if you select PLAYLIST for the AREA item, y

TASCAM DR-07MKII 85Editing the playlistYou can view and edit the playlist you have made on the PLAYLIST screen.You can also use this screen to play t

86 TASCAM DR-07MKIIPress the Á button to remove all the les or the (HOME) [ª] button to cancel this operation.For this operation, it does not matte

TASCAM DR-07MKII 87Selecting files for playback (skip)When the Home Screen is open, press the  and ¯ buttons to select the le for playback. If you

88 TASCAM DR-07MKIIRewinding and fast-forwarding (search) When the Home Screen is open and a track is playing back or stopped, press and hold the Â

TASCAM DR-07MKII 89NOTEIf you start loop playback, the REPEAT item automatically switches to OFF if it is in a different mode.5 Press the (HOME) [ª]

TASCAM DR-07MKII 9Table of ContentsSetting the playback area (AREA) ...80Selecting a folder for the playback area (1) ...82Selecting

90 TASCAM DR-07MKIIRepeated Playback of Selection (Loop Playback)With this function, you can continuously repeat (loop) the playback of a selection t

TASCAM DR-07MKII 91NOTEThe pop-up message of “I/O Too Short” appears if the •section between the IN and OUT points is too short. Set them again. The

92 TASCAM DR-07MKIIUsing the playback equalizer (PLAY EQ)You can choose from dierent sound types to enhance the listenability (PLAY EQ: playback equ

TASCAM DR-07MKII 93Moving back a few seconds for replay (jump-back playback) Press the Á button during playback to move back a few seconds (adjustabl

94 TASCAM DR-07MKIIFeatures of the QUICK buttonThe QUICK button serves for the following purposes.While the Home Screen is open and when stopped •or

TASCAM DR-07MKII 95Quick menu screenTo show the Quick menu screen, press the QUICK button while the Home Screen is open. The contents of this screen

96 TASCAM DR-07MKIISelect LEVEL CTRL, and press the Á button to open the level control setting pop-up window.In this window, you can choose from the

TASCAM DR-07MKII 97Closing the Quick menu screenPress the QUICK button to close the Quick menu screen.Deleting the selected file (Quick Delete)The cu

98 TASCAM DR-07MKII3 Use the + or − button to select DIVIDE, and press the Á button.DIVIDE screen appears.4 Use the + or − button to select to speci

TASCAM DR-07MKII 99CAUTIONMP3 files cannot be divided. •If the microSD card has insufficient open space, division •might not be possible. Division